LocostUSA.com
http://www.locostusa.com/forums/

MYTF's Haynes V6 RX-7 build
http://www.locostusa.com/forums/viewtopic.php?f=35&t=6245
Page 4 of 21

Author:  MYTF [ October 24, 2009, 10:57 pm ]
Post subject:  Re: MYTF's Haynes V6 RX-7 build

I can't post Autocad files here so send me a personal message with your e-mail address and I will send you the Autocad files.

Author:  MYTF [ December 12, 2009, 10:19 pm ]
Post subject:  Re: MYTF's Haynes V6 RX-7 build

I can’t believe it’s been a month and a half since my last post though my work has kept me pretty busy. Anyway I have taken the frame off the build table, built a 1” lower angle and tube support under the transmission and along side the engine and cut the tube that runs under the bellhousing to lower the engine.
I cut down the steering rack and mounted it. Trimmed and mounted my seats but am unhappy with them so I will probably get something else.
I bought two pinto motor mounts from NAPA for $38 and finally got the engine/transmission mounted today and am setting up the steering shaft to clear the future headers.
I picked up a two stage dry sump pump that came from a formula ford for $136 and I think I’ll build an aluminum pan to replace the steel one as I’m to happy with that either.

Attachments:
Locost7 032.jpg
Locost7 032.jpg [ 187.81 KiB | Viewed 6209 times ]
Locost7 031.jpg
Locost7 031.jpg [ 182.38 KiB | Viewed 6207 times ]
Locost7 030.jpg
Locost7 030.jpg [ 186.29 KiB | Viewed 6209 times ]
File comment: Transmission mount
Locost7 029.jpg
Locost7 029.jpg [ 189.26 KiB | Viewed 6209 times ]
Locost7 028.jpg
Locost7 028.jpg [ 162.03 KiB | Viewed 6210 times ]
Locost7 036.jpg
Locost7 036.jpg [ 203.99 KiB | Viewed 6207 times ]
Locost7 035.jpg
Locost7 035.jpg [ 215.61 KiB | Viewed 6201 times ]
Locost7 034.jpg
Locost7 034.jpg [ 223.44 KiB | Viewed 6200 times ]

Author:  Miatav8,MstrASE,A&P,F [ December 13, 2009, 8:38 am ]
Post subject:  Re: MYTF's Haynes V6 RX-7 build

Well done. You could add a few lightening holes with a hole saw in the flanges and clip a couple corners on the base plate on the mounts if you want to make them works of art.

Author:  MYTF [ December 15, 2009, 10:57 pm ]
Post subject:  Re: MYTF's Haynes V6 RX-7 build

The problem with asymmetry

I am laying out my dash and I can’t figure how to get the top and bottom to look good as the transmission tunnel is offset to the right. Any ideas?

Attachments:
IMG_0950.JPG
IMG_0950.JPG [ 199.2 KiB | Viewed 5993 times ]
IMG_0951.JPG
IMG_0951.JPG [ 196.59 KiB | Viewed 5989 times ]

Author:  natec [ December 15, 2009, 11:47 pm ]
Post subject:  Re: MYTF's Haynes V6 RX-7 build

I think you'd either want to move the gauges over and center the whole thing in the offset area, or make sure the offset is really obvious so doesn't just look 'off'. If that makes sense. :)

Author:  Miatav8,MstrASE,A&P,F [ December 16, 2009, 9:04 am ]
Post subject:  Re: MYTF's Haynes V6 RX-7 build

Ditto on center the cluster over the trans tunnel. Make the oval large enough not to obscure any cluster indications, then add fillers around the panel to make the cluster appear oval (green).

Attachments:
dashing doodle.JPG
dashing doodle.JPG [ 40.64 KiB | Viewed 5927 times ]

Author:  Flipper_1938 [ December 16, 2009, 11:20 am ]
Post subject:  Re: MYTF's Haynes V6 RX-7 build

Move the cluster in front of the driver.

Author:  MYTF [ December 16, 2009, 11:15 pm ]
Post subject:  Re: MYTF's Haynes V6 RX-7 build

Thanks for all your replies
Flipper_1938 wrote:
Move the cluster in front of the driver.

I can't it won't fit.

Miatav8,MstrASE,A&P,F wrote:
Ditto on center the cluster over the trans tunnel. Make the oval large enough not to obscure any cluster indications, then add fillers around the panel to make the cluster appear oval (green).

I love that idea! Always had a soft spot for the ellipse.
I'm going to work on that, if I can't get that to work I'll try the large offset method.

Author:  MYTF [ December 24, 2009, 10:55 pm ]
Post subject:  Re: MYTF's Haynes V6 RX-7 build

No work today so I worked on the dash. I'm using some 3/8 sch40 stainless pipe and I could not get the tight bends and it's not quite even but I think it looks OK.
Attachment:
Locost7 043.jpg
Locost7 043.jpg [ 207.13 KiB | Viewed 5595 times ]
Attachment:
Locost7 044.jpg
Locost7 044.jpg [ 197.17 KiB | Viewed 5595 times ]

I also switched the steering to above the frame and I was able to retain the tilt though it is upside down.
Attachment:
Locost7 038.jpg
Locost7 038.jpg [ 230.08 KiB | Viewed 5593 times ]
Attachment:
Locost7 037.jpg
Locost7 037.jpg [ 192.85 KiB | Viewed 5591 times ]

Someone on the list was conserned about the speedo cable so I thought I better check. It looks like with a 1in. bulge in the panel I won't have a problem.
Attachment:
Locost7 042.jpg
Locost7 042.jpg [ 146.81 KiB | Viewed 5595 times ]


Attachments:
Locost7 041.jpg
Locost7 041.jpg [ 215.32 KiB | Viewed 5590 times ]
Locost7 041.jpg
Locost7 041.jpg [ 215.32 KiB | Viewed 5590 times ]

Author:  Miatav8,MstrASE,A&P,F [ December 25, 2009, 8:10 am ]
Post subject:  Re: MYTF's Haynes V6 RX-7 build

That looks good and even; much better than the shape of the cluster.

Did you make the black boot on the tilt lever?

Author:  MYTF [ December 25, 2009, 2:32 pm ]
Post subject:  Re: MYTF's Haynes V6 RX-7 build

Actually that's the end of the existing lever. I just cut it and moved it over and down.
My thinking on the gages is to use what I have and later spend the money and get some good ones. With the dash split I can just make a new section for the gages.
Awhile ago I modified my seats to fit but I'm not sure if i will use them as they are not the same style. I was able to retain the tilt on the drivers side without the spring but there is not much room for the belts.

Attachments:
Locost7 040.jpg
Locost7 040.jpg [ 210.29 KiB | Viewed 5502 times ]

Author:  MYTF [ January 27, 2010, 1:03 am ]
Post subject:  Re: MYTF's Haynes V6 RX-7 build

No work means no money so I'm adjusting the build schedule a little.
I picked up some free 20 ga. stainless steel and thought I would use some for the floor. I know, I know it's to thin but I think I can make it work. I made a couple of forming tools, one for putting some creases to add a little stiffness and a flanging tool for holes.

Attachments:
File comment: Drivers side floor
IMG_0981.JPG
IMG_0981.JPG [ 96.51 KiB | Viewed 5292 times ]
File comment: Placed the sheet between the two 1/2" plates and hammered a 3/4" bar to make a dent
IMG_0977.JPG
IMG_0977.JPG [ 102.03 KiB | Viewed 5292 times ]
IMG_0978.JPG
IMG_0978.JPG [ 98.1 KiB | Viewed 5292 times ]
File comment: Turned these on the lathe to flange the holes.
IMG_0980.JPG
IMG_0980.JPG [ 108.02 KiB | Viewed 5291 times ]
File comment: This really stiffens things up
IMG_0979.JPG
IMG_0979.JPG [ 83.46 KiB | Viewed 5288 times ]

Author:  MYTF [ February 3, 2010, 11:20 pm ]
Post subject:  Re: MYTF's Haynes V6 RX-7 build

I could never make money at this! I've been working on my dash and thought I should post some pics.
I'm working on the gage panel now and will post on the soon I hope.
I'm not sure about the engine turned stainless for the panels they will probably be to bright and I might paint them in the future.

Attachments:
IMG_0992.JPG
IMG_0992.JPG [ 139.99 KiB | Viewed 5161 times ]
File comment: Engine turned panels.
IMG_0995.JPG
IMG_0995.JPG [ 132.26 KiB | Viewed 5162 times ]
File comment: Back of dash showing three of the four separate panels.
IMG_0996.JPG
IMG_0996.JPG [ 145.83 KiB | Viewed 5158 times ]
File comment: Wheel tilted down
IMG_0994.JPG
IMG_0994.JPG [ 108.8 KiB | Viewed 5157 times ]
File comment: With wheel tilted up
IMG_0993.JPG
IMG_0993.JPG [ 107.9 KiB | Viewed 5157 times ]

Author:  RWHARTMANN [ February 4, 2010, 12:38 am ]
Post subject:  Re: MYTF's Haynes V6 RX-7 build

I have an engine turned stainless dash in my car and its not that bad.

Ralph

Author:  natec [ February 4, 2010, 1:56 am ]
Post subject:  Re: MYTF's Haynes V6 RX-7 build

Wow. Just awesome. I'm pretty jealous right now. I like the collar on the steerwheel. How'd you make the rounded bevel when its also bending the other way (does that make sense?)

Page 4 of 21 All times are UTC - 5 hours [ DST ]
Powered by phpBB® Forum Software © phpBB Group
https://www.phpbb.com/