LocostUSA.com

Learning how to build Lotus Seven replicas...together!
It is currently July 17, 2018, 7:51 am

All times are UTC - 5 hours [ DST ]




Post new topic Reply to topic  [ 9 posts ] 
Author Message
PostPosted: June 23, 2018, 6:18 pm 
Offline
User avatar

Joined: November 11, 2013, 4:47 am
Posts: 875
Location: No. Nevada
OK, it seems I have a basic error problem?
Read several books and have tried to follow discussions here.
Have a suspension analysis program on an old PC.

Now that I have determined which ball-joints I will be using I wanted to get to work on A arms and mounting points to the chassis.
As others have posted a lot of the points are pre-determined by the spindle/upright chosen and the chassis*.

It seems that no matter what I try I cannot get negative camber in roll without bump going crazy.
I've been assured that negative camber in roll is not difficult, so I must be making a basic error of some sort.
3" compression and 2" droop travel.
Despite all the reading I have done it seems there are no "Ideal" numbers to shoot for, lots of theory but no numbers.
The assumption I've been working with is that the theoretical ideal would be zero camber at all times.
"Best?" camber I've gotten is around -4º at full bump and about +2º to +3º in roll.
*In my case the inner mount points can still be located wherever I want, within a range of several inches laterally and vertically.

No drawing yet but here are the basic dimensions.
For a level lower arm I need to be 8" from the ground at both ends.
Using -1º camber as the static ride height number.
Lower arm 10" - 11" (Max) long. Upper arm 2/3's of lower, angled less than 10º.
Spindle BJ mounts 10" apart.
Lower BJ 8" from ground.
Upper BJ 1.0" off-set to the inside.

Lower arms are to be the classic A type, BJ outer and rod-end inner.
Upper is a heavy arm from the BJ strait to the inner pivot rod-end and a leading arm going forward to a rod-end.
This is very similar to the original Alfa setup and gives me the most room for the engine and accessories.

I know I need to work up some more exact wheel and spindle drawings but thought I should be able to get close for basic suspension numbers.

_________________
If I must be a one-man PC free zone, so be it!


Top
 Profile  
Reply with quote  
PostPosted: June 23, 2018, 11:54 pm 
Offline
User avatar

Joined: July 4, 2006, 5:40 pm
Posts: 1916
Location: Novato, CA
Richard, you'll never get perfect camber in both bump and roll. They actually work against each other, so that improving one hurts the other. It's a compromise. Generally you want to reduce the amount of positive camber increase in roll by about half. So if for example the car rolls three degrees in a turn, you want around one and a half degrees positive camber. Then in bump you'll only get a degree and a half negative camber, for the same amount of travel. It'll never be perfect but you can tweak things later by decreasing static camber.


Top
 Profile  
Reply with quote  
PostPosted: June 24, 2018, 12:16 am 
Offline
User avatar

Joined: November 11, 2013, 4:47 am
Posts: 875
Location: No. Nevada
So what is a good to excellent number to shoot for, camber in bump at 3" to 4" travel?
Can't go more as I only have 5" ground clearance at ride height.
50" track, 90" wheelbase.
With this I can at least work on laying out A arm drawings.

I'm about to try to improve on my rough spindle measurements.

_________________
If I must be a one-man PC free zone, so be it!


Top
 Profile  
Reply with quote  
PostPosted: June 24, 2018, 9:26 am 
Offline
Always Moore!
User avatar

Joined: November 9, 2007, 3:40 pm
Posts: 3931
Location: Fort Worth, TX
There isn't a good number. It all depends on how much the springs and bars let the chassis move and how much caster and KPI you're running (caster will add negative camber to the outside wheel and KPI does the opposite).

_________________
-Andrew
Build Log
Youtube


Top
 Profile  
Reply with quote  
PostPosted: June 24, 2018, 11:53 am 
Offline
Mid-Engined Maniac

Joined: April 23, 2006, 8:26 pm
Posts: 5869
Location: SoCal
Picture a triangle. At one corner is "perfect camber under acceleration"; in the second it's "perfect camber under braking", and in the third, "perfect camber in roll." Pick your point between them.

_________________
Midlana book: Build this mid-engine Locost!, http://www.midlana.com/
Kimini book: Designing mid-engine cars using FWD drivetrains, http://www.kimini.com/book_info/


Last edited by KB58 on June 25, 2018, 12:39 am, edited 1 time in total.

Top
 Profile  
Reply with quote  
PostPosted: June 25, 2018, 12:35 am 
Offline
User avatar

Joined: April 26, 2008, 6:06 pm
Posts: 2949
Location: Under the weather. (Seattle)
If the steering effects aren't being factored in with the roll, then the numbers are pretty much meaningless.

_________________
-Justin

Also follow my build on blogspot, tumblr, or instagram and twitter (GarageOdyssey)


Top
 Profile  
Reply with quote  
PostPosted: June 25, 2018, 1:36 am 
Offline
User avatar

Joined: November 11, 2013, 4:47 am
Posts: 875
Location: No. Nevada
I think that if I can put together a list of the fixed values I should be able to find a Pro to work out the rest.
Not "Getting it" on my own despite many hours trying.
Would rather put my time into fabbing parts!
Anyone here qualified to take this on?

_________________
If I must be a one-man PC free zone, so be it!


Top
 Profile  
Reply with quote  
PostPosted: June 25, 2018, 7:13 am 
Offline

Joined: August 28, 2010, 7:53 am
Posts: 178
Some cars use more static camber with less gain in bump.....can cause other issues if you go too far (just like everything else) but it is another tool. By observation, German cars seem to do this on the rear more than others.

Off setting the kingpin axis can help camber on both wheels when turning. My solstice spindles do this, as well as a bunch of others. I am sure too much can cause problems too.


Top
 Profile  
Reply with quote  
PostPosted: June 25, 2018, 12:38 pm 
Offline
User avatar

Joined: April 26, 2008, 6:06 pm
Posts: 2949
Location: Under the weather. (Seattle)
I'm not sure what software you've been using, but the 'Wishbone' suspension program will perform the 3D analysis that allows you to factor steering inputs in conjunction with roll.

http://locostusa.com/forums/viewtopic.php?f=26&t=11985

_________________
-Justin

Also follow my build on blogspot, tumblr, or instagram and twitter (GarageOdyssey)


Top
 Profile  
Reply with quote  
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 9 posts ] 

All times are UTC - 5 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 2 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
POWERED_BY