LocostUSA.com

Learning how to build Lotus Seven replicas...together!
It is currently March 28, 2024, 8:51 am

All times are UTC - 5 hours [ DST ]




Post new topic Reply to topic  [ 26 posts ]  Go to page 1, 2  Next
Author Message
 Post subject: Plastic Body Panels
PostPosted: August 21, 2008, 2:36 pm 
Offline

Joined: December 17, 2007, 1:17 pm
Posts: 558
Wondering if a few of the straight panels could be done easily enough in plastic?

Buy a roll of this stuff:
http://www.speedwaymotors.com/p/1557,22 ... astic.html

Seems like it would work nicely for the side panels at a minimum. Would you glue it on or rivet? I'm curious as to how flexible it is for tight creases etc.


Top
 Profile  
Reply with quote  
 Post subject:
PostPosted: August 21, 2008, 4:13 pm 
Offline
The voice of reason
User avatar

Joined: January 10, 2008, 4:47 pm
Posts: 7652
Location: Massachusetts
They aren't providing much of a description "Plastic". At 1/8 inch thick it shouldn't be super flexible, but on the other hand they send it to you in a roll.

You would need large diameter rivets, not to wear holes in it. But rivets with washers and bonding might work well. Some plastics are hard to bond, like polyethylene.

Another choice would be to layup a panel of fiberglass on something flat. Say 2 or 3 layers of cloth and then cut to fit. Not sure there would be any advantage to aluminum though.

The colored plastic looks easy, and they are selling it for bodywork. I wonder if you could fold the edges around tubing? Buy a roll and let us know?

_________________
Marcus Barrow - Car9 an open design community supported sports car for home builders!
SketchUp collection for LocostUSA: "Dream it, Build it, Drive it!"
Car9 Roadster information - models, drawings, resources etc.


Top
 Profile  
Reply with quote  
 Post subject:
PostPosted: September 26, 2008, 12:17 pm 
Offline

Joined: December 17, 2007, 1:17 pm
Posts: 558
horizenjob wrote:
Buy a roll and let us know?


Did just that. They are selling it in 2' sections, so I bought 4'. It's quite tough stuff. 1/8" as stated, took about ten cuts with a box cutter to cut off a little piece. Bends and (mostly) keeps it shape quite nicely. Think it could work well. Saves money in spades over sheets of metal, and no need to paint!


Top
 Profile  
Reply with quote  
 Post subject:
PostPosted: September 26, 2008, 12:34 pm 
Interesting! Does it seem similar to the stuff they mold kayaks out of? That stuff is tough as nails...gotta keep heat away from it, though...


Top
  
Reply with quote  
 Post subject:
PostPosted: September 26, 2008, 1:30 pm 
Offline

Joined: December 17, 2007, 1:17 pm
Posts: 558
zetec7 wrote:
Interesting! Does it seem similar to the stuff they mold kayaks out of? That stuff is tough as nails...gotta keep heat away from it, though...


No idea. I want to see what it does under a heat gun as well. Might make it more pliable, or ruin it... we will see.


Top
 Profile  
Reply with quote  
 Post subject:
PostPosted: September 26, 2008, 2:18 pm 
Offline
User avatar

Joined: July 19, 2007, 4:09 pm
Posts: 550
Location: Austin, Tx
The colored plastics are usually used for air dams. At least thats what I was told it was for at the local race shop (lots of drag and american iron guys go there). They have rolls of it laying there.

Next time I'm there I'll snag some. I need to build an air dam on the front of the 90 miata anyway.


Top
 Profile  
Reply with quote  
 Post subject:
PostPosted: September 26, 2008, 3:36 pm 
Offline

Joined: August 15, 2005, 10:13 pm
Posts: 7043
Location: Charleston, WV
I don't think it would work on the side with the exhaust. I work with plastic sheet daily and I can assure you there will be mad warpage when it is heated. The amount of linear expansion and contraction of plastic as it is heated and cooled will suprise most folks.

Measure your 4' piece after a night in the AC and then set it out in the sun one day and measure it after it heats up. The results may suprise you.

_________________
He is a wise man who does not grieve for the things which he has not, but rejoices for those which he has.


Top
 Profile  
Reply with quote  
 Post subject:
PostPosted: October 5, 2008, 7:18 pm 
Offline

Joined: September 13, 2005, 5:58 pm
Posts: 191
Best part about this stuff is that it's self-adjusting for ride height. Nail it on, hanging nice and low, using those color-coordinated rivets with the oversized heads. Make a couple laps, and it will be shaved down to
perfect ground clearance!


Top
 Profile  
Reply with quote  
 Post subject:
PostPosted: October 6, 2008, 12:41 am 
Offline
Auto Motive, My friends call me Motive
User avatar

Joined: October 23, 2007, 11:56 pm
Posts: 270
Location: Spanish Fork, UT
check out this build log. He used plastic sheets all though not very cleanly.
http://www.absurdcars.com/page3.html


Top
 Profile  
Reply with quote  
 Post subject:
PostPosted: October 6, 2008, 2:18 am 
Offline
Weight watcher
User avatar

Joined: March 7, 2006, 6:15 pm
Posts: 2401
Location: Northridge, CA
Another problem with plastic is that the area that you'll heat up will become brittle.

Moti

_________________
Moti

My R1 powered Locost build log

Visit the Blackbird Fabworx Facebook Page!


Top
 Profile  
Reply with quote  
 Post subject: Re: Plastic Body Panels
PostPosted: September 18, 2017, 6:47 am 
Offline

Joined: May 22, 2017, 7:36 am
Posts: 163
Any update on this, how did it work out?

Updated link to product:

https://www.speedwaymotors.com/Colored- ... 910041-WHT


Top
 Profile  
Reply with quote  
 Post subject: Re:
PostPosted: September 18, 2017, 9:03 am 
Offline
Mid-Engined Maniac

Joined: April 23, 2006, 8:26 pm
Posts: 6410
Location: SoCal
chetcpo wrote:
I don't think it would work on the side with the exhaust. I work with plastic sheet daily and I can assure you there will be mad warpage when it is heated. The amount of linear expansion and contraction of plastic as it is heated and cooled will suprise most folks.

Measure your 4' piece after a night in the AC and then set it out in the sun one day and measure it after it heats up. The results may suprise you.

I'd expect warpage to be a problem then once it's trapped by rivets.

_________________
Midlana book: Build this mid-engine Locost!, http://midlana.com/stuff/book/
Kimini book: Designing mid-engine cars using FWD drivetrains
Both available from https://www.lulu.com/


Top
 Profile  
Reply with quote  
 Post subject: Re: Plastic Body Panels
PostPosted: September 18, 2017, 4:29 pm 
Offline
User avatar

Joined: July 4, 2006, 5:40 pm
Posts: 1994
Location: Novato, CA
Interesting the direction some people were going 10 years ago. I'm assuming the plastic didn't work as well as hoped for the OP.


Top
 Profile  
Reply with quote  
 Post subject: Re: Plastic Body Panels
PostPosted: September 18, 2017, 6:52 pm 
Offline

Joined: May 22, 2017, 7:36 am
Posts: 163
Ah heck with it, I ordered a roll of white to see how it works for the tub. If nothing else it will come in useful elsewhere i'm sure. Who doesn't need a 10ft roll of plastic trying to unravel in the garage?!


Top
 Profile  
Reply with quote  
 Post subject: Re: Plastic Body Panels
PostPosted: September 18, 2017, 11:51 pm 
Offline
User avatar

Joined: October 24, 2008, 2:13 pm
Posts: 5326
Location: Carlsbad, California, USA
aidandebradney wrote:
Ah heck with it, I ordered a roll of white to see how it works for the tub. If nothing else it will come in useful elsewhere i'm sure. Who doesn't need a 10ft roll of plastic trying to unravel in the garage?!


Let us know how it goes. Photos appreciated.

Cheers,

_________________
Damn! That front slip angle is way too large and the Ackerman is just a muddle.

Build Log: viewtopic.php?f=35&t=5886


Top
 Profile  
Reply with quote  
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 26 posts ]  Go to page 1, 2  Next

All times are UTC - 5 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 14 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
POWERED_BY